NPT Pipe Thread Chart
Look up NPT, NPTF, and BSPT pipe thread dimensions. This chart includes tap drill sizes, threads per inch, major/minor/pitch diameters, and engagement lengths per ASME B1.20.1.
NPT Pipe Thread Chart
| PIPE SIZE | TPI | MAJOR DIA (IN) | MINOR DIA (IN) | PITCH DIA (IN) | TAP DRILL SIZE | ENGAGEMENT LENGTH (IN) | BSPT EQUIVALENT |
| 1/16″ NPT | 27 | 0.3125 | 0.2611 | 0.27118 | C (0.242″) | 0.160 | — |
| 1/8″ NPT | 27 | 0.405 | 0.3537 | 0.36351 | R (0.339″) | 0.160 | 1/8″ BSPT |
| 1/4″ NPT | 18 | 0.540 | 0.4723 | 0.47739 | 7/16″ (0.4375″) | 0.228 | 1/4″ BSPT |
| 3/8″ NPT | 18 | 0.675 | 0.6073 | 0.61201 | 37/64″ (0.5781″) | 0.240 | 3/8″ BSPT |
| 1/2″ NPT | 14 | 0.840 | 0.7565 | 0.76843 | 23/32″ (0.7188″) | 0.320 | 1/2″ BSPT |
| 3/4″ NPT | 14 | 1.050 | 0.9665 | 0.97843 | 59/64″ (0.9219″) | 0.339 | 3/4″ BSPT |
| 1″ NPT | 11.5 | 1.315 | 1.2135 | 1.21363 | 1-5/32″ (1.1562″) | 0.400 | 1″ BSPT |
| 1-1/4″ NPT | 11.5 | 1.660 | 1.5585 | 1.55863 | 1-1/2″ (1.5000″) | 0.420 | 1-1/4″ BSPT |
| 1-1/2″ NPT | 11.5 | 1.900 | 1.7985 | 1.79863 | 1-47/64″ (1.7344″) | 0.420 | 1-1/2″ BSPT |
| 2″ NPT | 11.5 | 2.375 | 2.2735 | 2.27363 | 2-7/32″ (2.2188″) | 0.436 | 2″ BSPT |
| 2-1/2″ NPT | 8 | 2.875 | 2.7194 | 2.76216 | 2-5/8″ (2.6250″) | 0.682 | 2-1/2″ BSPT |
| 3″ NPT | 8 | 3.500 | 3.3444 | 3.38716 | 3-1/4″ (3.2500″) | 0.766 | 3″ BSPT |
| 4″ NPT | 8 | 4.500 | 4.3444 | 4.38716 | 4-1/4″ (4.2500″) | 0.844 | 4″ BSPT |
| 1/16″ NPTF | 27 | 0.3125 | 0.2611 | 0.27118 | C (0.242″) | 0.160 | — |
| 1/8″ NPTF | 27 | 0.405 | 0.3537 | 0.36351 | R (0.339″) | 0.160 | — |
| 1/4″ NPTF | 18 | 0.540 | 0.4723 | 0.47739 | 7/16″ (0.4375″) | 0.228 | — |
| 3/8″ NPTF | 18 | 0.675 | 0.6073 | 0.61201 | 37/64″ (0.5781″) | 0.240 | — |
| 1/2″ NPTF | 14 | 0.840 | 0.7565 | 0.76843 | 23/32″ (0.7188″) | 0.320 | — |
| 3/4″ NPTF | 14 | 1.050 | 0.9665 | 0.97843 | 59/64″ (0.9219″) | 0.339 | — |
| 1″ NPTF | 11.5 | 1.315 | 1.2135 | 1.21363 | 1-5/32″ (1.1562″) | 0.400 | — |
| 1-1/4″ NPTF | 11.5 | 1.660 | 1.5585 | 1.55863 | 1-1/2″ (1.5000″) | 0.420 | — |
| 1-1/2″ NPTF | 11.5 | 1.900 | 1.7985 | 1.79863 | 1-47/64″ (1.7344″) | 0.420 | — |
| 2″ NPTF | 11.5 | 2.375 | 2.2735 | 2.27363 | 2-7/32″ (2.2188″) | 0.436 | — |
| 1/8″ BSPT (R1/8) | 28 | 0.383 | 0.337 | 0.3566 | 8.6 mm (0.339″) | 0.148 | ≈ 1/8″ NPT |
| 1/4″ BSPT (R1/4) | 19 | 0.518 | 0.460 | 0.4868 | 11.5 mm (0.453″) | 0.209 | ≈ 1/4″ NPT |
| 3/8″ BSPT (R3/8) | 19 | 0.656 | 0.598 | 0.6248 | 15.0 mm (0.591″) | 0.224 | ≈ 3/8″ NPT |
| 1/2″ BSPT (R1/2) | 14 | 0.825 | 0.750 | 0.7842 | 18.6 mm (0.732″) | 0.291 | ≈ 1/2″ NPT |
| 3/4″ BSPT (R3/4) | 14 | 1.041 | 0.966 | 1.0003 | 24.1 mm (0.949″) | 0.311 | ≈ 3/4″ NPT |
| 1″ BSPT (R1) | 11 | 1.309 | 1.214 | 1.2572 | 30.5 mm (1.201″) | 0.409 | ≈ 1″ NPT |
| 1-1/4″ BSPT (R1-1/4) | 11 | 1.650 | 1.555 | 1.5982 | 39.2 mm (1.543″) | 0.430 | ≈ 1-1/4″ NPT |
| 1-1/2″ BSPT (R1-1/2) | 11 | 1.882 | 1.787 | 1.8302 | 44.8 mm (1.764″) | 0.430 | ≈ 1-1/2″ NPT |
| 2″ BSPT (R2) | 11 | 2.347 | 2.252 | 2.2952 | 56.7 mm (2.232″) | 0.449 | ≈ 2″ NPT |
| 2-1/2″ BSPT (R2-1/2) | 11 | 2.960 | 2.865 | 2.9082 | 72.2 mm (2.843″) | 0.449 | ≈ 2-1/2″ NPT |
| 3″ BSPT (R3) | 11 | 3.460 | 3.365 | 3.4082 | 84.8 mm (3.339″) | 0.449 | ≈ 3″ NPT |
| 4″ BSPT (R4) | 11 | 4.460 | 4.365 | 4.4082 | 109.5 mm (4.311″) | 0.449 | ≈ 4″ NPT |
Quick Answer: What Is an NPT Pipe Thread?
NPT (National Pipe Taper) is the standard tapered pipe thread used in North America, defined by ASME B1.20.1. It has a 60° thread angle and a 3/4″ per foot taper (1°47′ on diameter). The taper wedges male and female threads together to form a seal. NPT is found in plumbing, pneumatics, hydraulics and fluid power ports.
This chart uses ASME B1.20.1 data so you can look up: threads per inch, major, minor and pitch diameter, tap drill size, and hand-tight engagement length. It also lists NPTF (dryseal) and BSPT equivalents per ISO 7/1. Search or filter by pipe size from 1/16″ to 4″.
Common tap drill sizes: 1/8″ NPT → R (0.339″) | 1/4″ NPT → 7/16″ (0.4375″) | 3/8″ NPT → 37/64″ (0.5781″) | 1/2″ NPT → 23/32″ (0.7188″) | 3/4″ NPT → 59/64″ (0.9219″). TPI ranges 27–8.
Notes on This Chart
- NPT dimensions are perASME B1.20.1. Major diameters are measured at the large end of the external thread.
- Pitch diameters are at the gauge plane (E1)— the reference point at the end of hand-tight engagement.
- Tap drill sizes are approximate starting points. The actual hole size may vary depending on material and tap manufacturer recommendations.
- All NPT threads have a taper of 3/4″ per foot(1°47′) on diameter.
- NPT and NPTF share the same basic dimensions, but NPTF has tighter crest/root tolerances for dryseal capability.
- BSPT dimensions are per ISO 7/1 (BS 21). BSPT uses a 55° thread angle vs. NPT’s 60°.
- NPT and BSPT are not interchangeabledespite similar nominal sizes. Mixing them will leak.
How to Use This NPT Pipe Thread Chart
Finding the right pipe thread dimensions is straightforward once you know what to look for:
- Identify the pipe size.NPT sizes are called out by nominal pipe size (NPS), not actual diameter. A “1/2 NPT” fitting does not have a 1/2″ outside diameter — it has a 0.840″ major diameter.
- Find the row in the chart.Use the search box or filter tabs to locate your pipe size and thread standard (NPT, NPTF, or BSPT).
- Read the dimensions.The major, minor, and pitch diameters tell you the thread geometry. The tap drill size tells you what drill to use before tapping an internal pipe thread.
- Check the engagement length.This is the hand-tight engagement length (L1). You will tighten 3–5 additional turns past this point with a wrench.
- Apply sealant.For NPT threads, always use PTFE tape or pipe dope. For NPTF (dryseal), sealant is optional but recommended for critical applications.
1/4 NPT Thread Dimensions — Quick Reference
1/4″ NPT is one of the most widely used pipe thread sizes. You will find it in pneumatic fittings, hydraulic ports, instrument connections, and fluid power manifolds. Here are the exact specifications:
| Specification | Value |
| Nominal Pipe Size | 1/4″ |
| Threads Per Inch (TPI) | 18 |
| Major Diameter (OD) | 0.540″ |
| Pitch Diameter (E1) | 0.47739″ |
| Minor Diameter | 0.4723″ |
| Tap Drill Size | 7/16″ (0.4375″) |
| Hand-Tight Engagement (L1) | 0.228″ (approx. 4.1 threads) |
| Effective Thread Length (L2) | 0.401″ (approx. 7.2 threads) |
| Taper | 3/4″ per foot (1°47′) |
Tip: When drilling for a 1/4″ NPT tap, use a 7/16″ drill bit (0.4375″). Drill deep enough to accommodate the full effective thread length plus the vanish threads at the bottom. For a through hole, drill all the way through and tap from one side.
NPT vs BSPT: Which Pipe Thread to Use
NPT and BSPT are both tapered pipe thread standards, but they are not interchangeable. Here is a side-by-side comparison:
| Feature | NPT | BSPT |
| Standard | ASME B1.20.1 | ISO 7/1 (BS 21) |
| Thread Angle | 60° | 55° |
| Taper Rate | 1:16 (3/4″/ft) | 1:16 (3/4″/ft) |
| Sealant Required | Yes (PTFE tape or pipe dope) | Yes (PTFE tape or pipe dope) |
| Region | North America | Europe, Asia, and other international markets |
| Thread Pitch (1/2″) | 14 TPI | 14 TPI |
| Cross-Compatible? | No | No |
When to use NPT: Any project destined for the North American market, plumbing per US codes, pneumatic/hydraulic systems in US-made equipment.
When to use BSPT: Export products, European/Asian equipment, systems that must comply with ISO standards.
NPT Thread Sealant Guide
- PTFE tape (Teflon tape).The most common sealant. Wrap 3–5 turns clockwise (looking at the thread end) around the male threads. Use yellow tape for gas lines, white tape for water and general purpose, green tape for oxygen systems.
- Pipe dope (thread compound).Brush it onto the male threads. Better than tape for large pipe sizes and high-vibration applications. Some compounds are rated for specific fluids or temperatures.
- Anaerobic thread sealant.Liquid sealants like Loctite 567 or Permatex that cure in the absence of air between metal surfaces. Good for high-pressure applications and permanent connections.
- NPTF (dryseal) threads.Designed to seal without sealant by crushing the thread crests and roots. However, sealant is still recommended for critical applications as insurance against micro-leaks.
- Do not use tape on NPTF threads in fuel/hydraulic systems— tape fragments can contaminate the fluid and clog filters or valves.
Need NPT tapped holes in your parts?
Upload your CAD file and we will handle the threading — NPT, NPTF, BSPT, and custom pipe threads. Internal and external, blind and through. Free DFM review included.
Frequently Asked Questions
What is NPT thread?
NPT (National Pipe Taper) is a tapered pipe thread standard defined by ASME B1.20.1. It uses a 60° thread angle and a 1:16 taper to create a tight seal as the male and female threads are tightened together. NPT threads are widely used in plumbing, pneumatic, hydraulic, and fluid power systems.
What is the tap drill size for 1/4 NPT?
The recommended tap drill size for 1/4 NPT is 7/16″ (0.4375″). This size provides the starting hole for tapping the 18-TPI 1/4 NPT thread. The finished hole should provide sufficient depth for the required thread engagement.
What is the difference between NPT and BSPT?
NPT uses a 60° thread angle, while BSPT uses a 55° thread angle. Both are tapered pipe threads with a 1:16 taper, but their different thread forms and dimensions make them non-interchangeable. NPT is commonly used in North America, while BSPT is widely used internationally.
How many threads per inch does 1/2 NPT have?
A 1/2 NPT thread has 14 TPI. Its nominal major diameter is 0.840″, with a pitch diameter of approximately 0.768″ at the gauge plane.
Do I need thread sealant on NPT fittings?
Standard NPT connections generally require a thread sealant, such as PTFE tape or pipe joint compound, to prevent leakage through the helical thread path. NPTF threads are designed as dryseal threads and can provide a metal-to-metal seal without conventional sealant when properly manufactured and assembled.
What is the difference between NPT and NPTF?
NPTF (National Pipe Taper Fuel) uses the same basic taper and 60° thread form as NPT, but its tighter crest and root dimensions are designed to produce a dryseal connection. NPTF is commonly used where avoiding thread sealant is important, including some fuel and hydraulic applications.
How far should NPT threads engage?
NPT fittings are typically tightened several turns beyond hand-tight, with the exact engagement depending on pipe size, material, fitting design, and application. Avoid excessive tightening because it can damage or crack fittings, particularly those made from softer materials.
What is the pitch diameter of 3/8 NPT?
The 3/8 NPT pitch diameter at the gauge plane is approximately 0.676″. This thread has 18 TPI, a 0.675″ nominal major diameter, and a minor diameter of approximately 0.612″.