Surface Finish Chart
Convert between Ra, Rz, and RMS surface roughness values. See which machining process gives the finish you need, from mirror polish to rough mill.
Surface Roughness Conversion Chart
| RA(MIN) | RA(MM) | RZ(MIN) | RMS (MIN) | N GRADE | MACHINING PROCESS | TYPICAL APPLICATION |
| 1 | 0.025 | 4 | 1.1 | N1 | Superfinish / Lapping | Optical mirrors, gauge blocks |
| 2 | 0.05 | 8 | 2.2 | N2 | Lapping / Polishing | Precision bearings, seals |
| 4 | 0.1 | 16 | 4.4 | N3 | Fine grinding | Hydraulic valve spools, piston rods |
| 8 | 0.2 | 32 | 8.9 | N4 | Grinding | Bearing journals, crankshaft pins |
| 16 | 0.4 | 63 | 17.8 | N5 | Fine grinding / Honing | Cylinder bores, sealing surfaces |
| 32 | 0.8 | 125 | 35.5 | N6 | Fine turning / Fine milling | Mating surfaces, close-fit shafts |
| 63 | 1.6 | 250 | 69.9 | N7 | Standard milling / Turning | General machined surfaces, brackets |
| 125 | 3.2 | 500 | 138.8 | N8 | Milling / Turning | Structural parts, non-critical faces |
| 250 | 6.3 | 1000 | 277.5 | N9 | Rough milling / Rough turning | Rough-machined castings, forgings |
| 500 | 12.5 | 2000 | 555 | N10 | Rough milling / Sawing | Raw stock surfaces, non-functional faces |
| 16 | 0.4 | 63 | 17.8 | N5 | Fine turning | Precision OD/ID fits, valve stems |
| 63 | 1.6 | 250 | 69.9 | N7 | Standard turning | Shafts, bushings, spacers |
| 32 | 0.8 | 125 | 35.5 | N6 | Fine wire EDM | Mold cavities, precision dies |
| 63 | 1.6 | 250 | 69.9 | N7 | Wire EDM | Stamping dies, extrusion dies |
| 125 | 3.2 | 500 | 138.8 | N8 | Sinker EDM | Deep ribs, complex mold shapes |
| 250 | 6.3 | 1000 | 277.5 | N9 | Rough sinker EDM | Roughing cavities, electrode burns |
Quick Answer: What Is Surface Finish (Ra, Rz and RMS)?
Surface finish is the measure of small peaks and valleys left on a machined part. Ra is the arithmetic average roughness and the most common spec on drawings. Rz is the average peak-to-valley height over a sample length. RMS is the root mean square of the same heights. A lower number means a smoother surface. These values are used to set fit, seal, wear and appearance requirements.
This chart converts between Ra, Rz, RMS and ISO 1302 N grades to show: Ra in microinches (μin), Ra in micrometers (μm), Rz value and RMS value, plus the matching N grade and machining process. Reference data covers superfinishing through rough milling, turning, grinding and EDM. RMS is about Ra × 1.11 for typical machined surfaces.
Typical Ra by process: Grinding/lapping: 1–16 μin (N1–N5) | Fine turning/milling: 32 μin (N6) | Standard milling/turning: 63–125 μin (N7–N8) | Rough milling: 250–500 μin (N9–N10).
Notes on This Chart
- Ra is arithmetic average roughness. RMS is approximately Ra x 1.11 for typical machined surfaces.
- Rz measures peak-to-valley height over a sample length. It is more sensitive to deep scratches.
- N grades follow ISO 1302. N1 is the smoothest. N12 is the roughest.
- Actual finish depends on material, tooling, speed, feed, and coolant. Always verify with a profilometer.
Need specific surface finishes on your parts?
Upload your CAD file for an instant quote. Free DFM review included with every order.
Frequently Asked Questions
What does Ra mean in surface finish?
Ra stands for arithmetic average roughness. It represents the average deviation of surface peaks and valleys from the mean line. The lower the Ra value, the smoother the surface. Among surface finish measurements, Ra is the most commonly specified value on engineering drawings.
How does Ra differ from RMS?
Ra calculates the arithmetic average of surface deviations, while RMS (root mean square) gives greater emphasis to larger peaks and valleys. For most machined surfaces, RMS is approximately 11% higher than Ra. As a quick estimate, multiply the Ra value by 1.11 to obtain the approximate RMS value.
What surface finish is achievable with CNC milling?
Typical CNC milling produces a surface finish of around 63 to 125 microinch Ra. Using sharp cutting tools and lighter cutting passes can improve the finish to approximately 32 microinch Ra. For finishes below 16 microinch Ra, additional processes such as grinding or polishing are generally required.
How should surface finish be indicated on an engineering drawing?
Specify the required finish using the standard surface finish symbol, which resembles a check mark, together with the required Ra value in microinches or micrometers. Apply the symbol directly to the surface where the finish requirement applies. Avoid specifying unnecessarily tight surface finishes, since tighter requirements generally increase machining and finishing costs.